吸附物式干澀機

◆成品優勢特點 Product features

※具備著穩定可靠一直的排氣氣壓和露點

1.吸塔之特別與直徑不低于經測試成果高精密核算，塔床摩擦阻力小，可以保障了減小混合氣體干熱劑5秒的接處時段，具備半成品氣的露點標準。

2.30％的烘干劑留量，用以補償金烘干劑的理所當然衰老，為了保證烘干。

3.超大型發展器，為了確保氣浪平滑確認變干劑層，清理溝流想象。

※回收氣量耗率超過14％

1.有遠見的機筒的設計，保護100％的吸咐能量，吸收的能量用作增添重復利用階段中的重復利用氣溫暖，提高了設施的解吸工作能力，可使得重復利用更充分。

2.吹干和回收主要包括返向平衡計劃書，濕環境流回干的吸收劑時間果極佳。回收氣出來含濕量把握在亞過飽和壯態，使消音器原理器及排氣口綠色通道無結霜之慮。

3.可只能根據空氣干燥機的操作裝載實際需求改善再造氣運用量，確定再造氣旋陸續不穩，再造負壓低至臨界點。

※潮濕劑食用保修期長

1.比較好的機筒大小，使氣體經由干劑層的流動速度和時間段堅持好的情形，充分的揮發干劑的安全性能。

2.合理可行的設計設備，在氣體流動打開機筒前，經除油處理迅速除掉氣體流動中內植物油成分物與重水被污染，防止晾干劑層受水被污染。

※機械設備通過了創新高品級電動伸縮及油路分配器閥和可靠的的全光電子可程序編寫序把控好器，組排頁面十分友好，自然維持表現雙塔工程狀況，循環往復階段環境可編，生產快速設置10min。調節閥 使用期短短50萬次拉伸動作。

※壓力容器封頭壁內作冷熱鍍鋅防腐補救，10年不浮銹。

※行為最準、效果維持、操作步驟簡單方便，按裝不能不基礎知識。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆核心技術應用參數設置 Main technical parameters